Generators

Generator Installation

At Tangora Technologies, Inc. our expert technicians will install the best quality whole house generator and provide exceptional service. We are a certified installation and service provider for Briggs and Stratton and Generac generators for both commercial and residential products. We are trained to evaluate the power load necessary to keep the entire property functioning when the power is out.

Typical installation usually includes the following:

One Briggs and Stratton generator on stone bed with treated lumber perimeter in discussed location
One Briggs and Stratton ACC transfer switch in discussed location
One gas line from existing gas supply to new generator location including all pipe fitting and gas shut off
One electrical disconnect for emergency service personal
One ground rod and bonding cable to ground outdoor generator to the Earth’s ground
All necessary interconnecting service cable generators to transfer switch cabling and control wire cabling
Complete start-up and commissioning with power outage simulation test
All customer orientation manuals and inspection

How much does a whole house generator cost?

Pricing is determined with Generator Sizing, Transfer Switch Selection, Materials, Travel and Labor. All residential generator installations qualify for Capital Improvement Exemptions, therefore, you do not pay tax on the installation. TTI provides FREE on-site estimates including full load test on house prior to generator/transfer switch selection. To schedule an appointment please contact the office at 518-478-9513 or contact Heather at heather@tangoratechnologies.com

Call 518-478-9513

Get a FREE Quote Schedule Service Request Information

Updates
Recent Posts

Generator Installation

Replacement

TTI provides a complete line of generators to replace any existing generator. When replacing the generator sizing comes into play.

Was the old generator supplying the property enough power?
Did the automatic switch perform to its capacity?

With newer smarter switch technology, typical sizing decreases due to the fail safe technology built into the ACC switch. For example, if the power fails, the ACC quickly determines the demand on the generator and decides what loads are safe for operation. With one or more HVAC systems, the ACC can decide when and/or if it’s safe to allow operation with a simple wiring interface. Likewise, any pump relay on an electrical device can interface with the smart transfer switch (ACC) as well – protecting the appliance as well as the generator. All generators exercise 20 minutes per week which is 17 hours a year. This ensures that the smaller standby generator can serve a purpose.

Let us provide an estimate for you on your generator replacement. Just schedule an appointment online or call our offices.

Call 518-478-9513

Get a FREE Quote Schedule Service Request Information

Updates
Recent Posts

Replacement

Maintenance/Service

Tangora Technologies, Inc. is a certified installation and service provider for both Generac and Briggs and Stratton generators. We provide annual service maintenance for all generator brands to ensure your equipment will test weekly and be ready when the power goes out. A happy customer is our goal and we strive for complete customer satisfaction while providing expert service for your generator.

Annual maintenance is recommended by factory for warranty as well as reliability. TTI provides complete Preventative Maintenance Agreements (PMA) ranging from $299.00 - $499.00 depending on size of generator.

The Generator PMA Includes:

Tune-up kit (Oil Filter, Synthetic Oil, Air Filter, Pre-Cleaner, Spark Plugs)
Schedule of maintenance:
Pull and replace spark plugs
Drain and Replace oil filter/oil change with synthetic oil
Pre-Cleaner for air filter
Air Filter
Value adjustment if necessary
Voltage check with meter
Motor frequency test
Regulator adjustment
Transfer switch test

Call 518-478-9513

Get a FREE Quote Schedule Service Request Information

Updates
Recent Posts

Maintenance/Service

Frequently Asked Questions

What is the difference between portable and automatic Home Generator Systems?
The differences have to do with the steps needed to have emergency power flowing into your house in the event of a power outage. Portable systems are wheeled units that require you to roll the generator outside, start it up, and hook it up to a power inlet box. From there you must go to the transfer switch panel installed near your circuit breakers and switch the power coming into your house from the main line to the generator running outside. After the power from your local utility is restored, you are required to reverse the setup process.

One of the clear advantages with an Automatic Home Generator System is that the unit turns itself on and off automatically without you ever having to leave the safety of your home. Our automatic Home Generator Systems also exercise themselves once a week. You can even set the time when the unit will perform this diagnostics check. The generator will then be ready to run whenever needed.

How does the Home Generator System work?
At the point of loss of utility power, the system will wait approximately 6 seconds to start (this is to verify that the power is going to stay out). After it has started it will go through a warm up period of 20 seconds. After this time the transfer switch will change over to generator power. The house will remain under generator power for a minimum of 5 minutes, even if the utility power comes back on. After utility has come back on, and the generator has powered up the house for at least 5 minutes, the transfer switch will go back to utility power after 10 seconds. The generator will then run 1 minute to cool down before turning itself off.

What size Standby generator do I need to run electric items in my house during a power outage?
Most average homes of 1200 to 3000 sq. ft. can run critical items in the home by using a 5000-7000 watt generator. The most common items that need emergency power during a blackout would be the furnace blower motor, refrigerator, freezer, lights, TV, sump pump, and water pumps. Larger Home Generator Systems in the 10-15KW range will quietly supply as much as 18,000 watts of starting power to your home automatically, giving your family the power, freedom and comfort of their usual lifestyle uninterrupted by power failure. The 12-20kW generators allow you to supply power to both essential items PLUS up to 6 high wattage appliances including 2 central air units for the ultimate in comfort and control.

Can I run a computer or other sensitive electronic equipment off the generator during a power outage?
Yes. The power coming from your generator is just as safe as what you normally have coming out of the wall socket. The spikes or surges that accompany power generation (also known as “harmonic distortion”) are just a normal aspect of electricity. However, when considering sensitive or expensive electronic equipment running off a wall outlet, you should use a good surge protector to guard against small influxes of power.

Does motor starting require a different wattage?
Yes. Induction motors require larger amounts of amperage for initial start-up than when they are running. Some appliances and tools, such as your refrigerator/freezer, furnace fan, air conditioner, electric chain saw, weed trimmer, etc. will require more watts than normal running wattage for motor starting. This must be considered when sizing a generator to meet your needs.

What does a Home Generator System typically cost?
When you choose the safety, reliability and automatic operation of a Home Generator System, there are several items that contribute to the total cost, the cost of the system itself, a transfer switch, and installation charges. Optional maintenance contracts can also add to the cost if you choose one. Costs may vary depending on the size of the unit, transfer switch used, location of installation, and permits required for installation. Check with TTI for more details.

Can I run my central air conditioner on the Home Generator System?
Yes. We have devised a transfer switch that will monitor loads on the generator, under emergency power, allowing you to run a central air unit at a 4-ton rating or less on our 12kW and 15kW Generator Systems. They are called our ACCM transfer switches. They are available in 100 or 200 amp sizes. We also offer a Power Management System to aid in running air conditioning systems.

What is a transfer switch?
A transfer switch is a device that is fed by both utility and generator power. It isolates the two types of power from each other so a back feed does not occur. National Electrical Code requires a device like this if two types of power are going to feed the house.

How do I know what size transfer switch I need?
There are many factors that will determine the size transfer switch needed (size of utility service, appliances needed to run, size of generator, etc). The transfer switches available vary from 50, 100 and 200 amps. The 100 and 200 amp transfer switches are for whole house power and feed the entire distribution panel.

What is the Power Management System and how can it benefit me?
With our ACCM transfer switch, there must be room on the generator for a central air unit to run. The Power Management System isolates six circuits from your main distribution panel to allow the air conditioner to start when it wants. Basically, the Power Management System makes room on the generator. These would be circuits that you would not mind being turned off for a short period of time while the A/C runs. You can hook these circuits up in priority, 1 is the highest priority and 6 is the lowest. Discuss with a dealer how you want each item hooked up.

How do I purchase one… who do I call?
If you are interested in learning more about our products, setting up an estimate or are looking for information on how to purchase, please call 518-478-9513 or email Heather@tangoratechnologies.com.

Can I install the unit myself or does someone else need to?
It is recommended that you have your Home Generator System (generator and transfer switch) installed by a licensed contractor. Failure to do so could be dangerous for both family members as well as outside repair workers trying to fix downed power lines. In addition, professional installation is required to maintain the warranty. They would also make sure that all the necessary permits are pulled to verify an inspector would pass it. Most Milbank Home Generator Systems dealers are capable of not only performing the necessary installation, but can also offer maintenance agreements that ensure the generator is being serviced on a regular basis. Tangora Technologies is the certified dealer/installer for our area.

What happens in a typical installation?
A basic installation includes:
• Delivery of the system to Tangora Technologies. Additional charges for drop ship to consumer.
• Installation of the transfer switch is then hardwired into your home or business.
• The transfer switch is installed within 2 feet of the main distribution panel and 30 feet of the generator inlet box.
• Final start up inspection of system and completion of start up form.
• Cleanup of installation debris after installation is completed.
• Consumer is responsible for making arrangements to provide all necessary gas service and connections..

What does Automatic Voltage Regulation (AVR) do for me?
The 7kW Home Standby System features AVR. AVR maintains a more steady voltage than something that is not regulated. This is especially important for running sensitive electronics such as computers, microwaves, and televisions.

What is the warranty?
The warranties will vary depending upon the unit that is purchased. Entry-level systems will carry a 2-year warranty; while more advanced systems carry a 3-year/1500 hour warranty. There is also a fourth year power train warranty with our more advanced units. To validate your warranty, simply return the postage paid installation checklist.

About Maintenance And Use

Do I need to start the generator frequently when it is not being used?
One of the advantages of the automatic Home Generator Systems is that they are designed to run once a week for twenty minutes. All you have to do is program when you want this task to be performed and it will start up automatically. During this time it will not only lubricate the engine, but it will also run a diagnostics check. If there are any problems with this process, an LED display located inside the front access panel or your in-home remote performance monitor will alert you to a problem if one exists.

How long will a unit run before I have to let it cool down or refill it with fuel?
Another advantage of our Home Generator Systems is that they run on liquid propane or natural gas, so they don't need to be refueled as often, if at all. Additionally, rest periods to allow cooling are not necessary. All Milbank Home Generator Systems are air- or liquid-cooled and do not require you to turn them off after extended run times. However, you will need to turn off the unit before refueling (if running on liquid propane) or when checking the oil levels which should be done on a regular basis during and after extended use (refer to your owner's guide for instructions).

Do I have to worry about “back feed” if the generator is running when the power comes back on?
No. All of our transfer switches are designed to keep generator back feed from occurring. When TTI installs the transfer switch, it will be connected directly to the utility power. A control board will be able to sense when the utility power has returned to transfer back to utility (it is programmed so the generator powers up the house for a minimum of five minutes). Everything is programmed so that one source of power is broken before another source of power is made.

How often do I have to change the oil?
The engine maintenance manual recommends 50-hour intervals between oil changes and 100-hour intervals for the oil filter. We do require that 5W30 fully synthetic oil be used when replacing the oil. This will enable the engine to stabilize quicker (it has 20 seconds to do this). All Home Generator Systems are shipped fully lubricated and the engines broken in; no break-in of the engine needs to be performed.

Who do I call if I have any questions or maintenance issues?
We recommend that you first contact TTI first. The best person to service the generator is the one with First-hand knowledge of your original system installation. That makes us best equipped to field questions and perform any needed maintenance. You can also call Briggs & Stratton directly at (800) 743-4115, Monday through Friday, 8am-5pm Central Time if TTI is not available or a problem requires additional help.

Can I vent exhaust out of an enclosed area?
No. Carbon monoxide gases produced by the engine could be deadly. Milbank Home Generator Systems are designed to be run outside only where there is plenty of ventilation. Never run these units inside a home or enclosed area. All Milbank Home Generator Systems are permanently installed outside your home.

Can I run the generator inside my home?
No! A generator has an internal combustion engine and uses gas and oil. The exhaust from running a generator contains lethal carbon monoxide. Therefore, this unit should always be placed in a well-ventilated area and never run or be installed in an enclosed area.

How can I get more information on Briggs and Stratton Home Generator Systems?
You can request information through our online request form.